Door slamming is an unpleasant occurrence in the household. It is a situation where a door is shut with great force causing it to make a loud noise. This slamming may happen as a result of some weights on the door. It can also occur because of someone shutting it by force. A little contact with the door may lead to slamming. A breeze from an open window or a vent can cause a door to suddenly slam closed. Door slam causes unwanted noise and disturbance which are incredibly annoying. It is even risky sometimes when a door loses control suddenly.

Apart from external forces that could make a door slam closed, some conditions may cause door slamming. Firstly, if the door is not perfectly vertical. In that capacity, the lopsidedness can prompt a swing because of the heaviness of the door or air current, which can make the door hammer shut. Secondly, there could be an issue with the pivots or hinges. They might be mounted erroneously or they might be distorted, which could cause awkwardness and cause the door to slam shut.

There are plenty of credible solutions to stop the door from slamming. Some are Do It Yourself procedures too that anyone can try to fix door slam. You can also get Anti Door Slam products for correcting the problem. We shall review the methods one after the other.

Tips to Stop Door from Slamming 2020

This is How to Stop Door from Slamming;

1. Inspect the Hinges

Hinges are the pivots that hold a door to a frame for balance and rotation. If the hinges are worn or not properly installed, then there will be an imbalance and this will cause the door to slam. Open your door to a 90-degree angle and then set a level against the latch to see if the door is out of plumb. Try to tighten the hinge screws and check if the condition is better. If no improvement is perceived, then replace the hinges. The new hinges will set up a firmer connection between the door and the frame. This will also restore the door back to the proper vertical position.

2. Use a Door Stop

This method is suitable for a door that wildly swings open or shut. The door stop will prevent this anytime the door moves. You can place a rubber door wedge-like Shepherd Hardware 9133 Heavy Duty Rubber Door Wedge under the door to keep it from moving. Installing Kickdown Door Stop is another product to stop the door.

3. Use Felt Pads

Place self-adhesive felt pads along the edges of the door frame. Place a few smaller pads on the top and bottom of the door’s strike plates. These pads are common on appliances to keep them from scratching the floor. Felt pads work like sound absorber when the door is shut. They also serve as cushions to slow down the rate of speed at which the door closes.

4. Install an Automatic Door Closer

Automatic door closers are devices that automatically closes the door after it has been opened. These air-powered devices attach between the doorframe and the door edge and use an air-filled piston to slowly swing the door closed. Most are adjustable, so you can slow the door’s swing down enough to prevent a slam.

To counteract the slamming problem, adjust the device to a speed and pressure setting that’s appropriate for your specific needs. Using a door closed is more versatile in a commercial environment, home and offices. A steel or aluminum door closer will be more durable and reliable. This could also serve as car door slamming prevention.

5. Apply Weather Stripping

Weatherstripping can likewise be utilized to prevent a door from slamming shut. Like the felt cushions referenced above, weather stripping gives padding, which assists with reducing the speed at which the door impacts with the frame, along these lines limiting slamming. It additionally assists with absorbing sound when the door comes in contact with the frame. Even when the door is closed by force, the strip will still dampen the slamming noise.

To use this technique, apply weather stripping along the inside of the door frame. Wipe down the door frame first to ensure that you have a spotless surface to apply the material to. Remove the backing from the adhesive and apply the weather stripping along within the door frame. This method will give better results on a more massive door than felt pads.

6. Use Door Pinch Guard

A pinch guard is fixed around the door, to keep the door over the frame thereby making it impossible to shut. Pinch guard was made with the intention of protecting the finger from being pinched, it can also assist with keeping a door from slamming. Preventing the door from shutting can eliminate the unwanted noise of slamming as well.

It has a small C shape foam provides a soft cushion between the door and the door frame and acts as a door draft stopper. The pinch guard will stop the door slamming in the wind coming in from an open window.

Place the pinch guard on the highest point of the door, with a minimum of six inches from the exterior angle. The pleasant thing about this choice is that it can be easily removed when you would prefer not to use it.

7. Install a Door Silencer

A door silencer is a conned shape little bit of rock-solid elastic material formed to a level roundabout support. Door silencer is another cheap and effective product to prevent door slam. They are common on heavy steel doors inside emergency clinics and schools. This rubber object can be installed on both metal doors and wooden doors.

To install a door silencer, drill a one-quarter hole into the doorstop section of the frame. Insert the rubber cone into the hole and apply pressure to keep it tight. The cushion part will act as a shock absorber when the door closes without making a slamming noise.

8. Cover the door Jamb with a Cushion

This cushion is made from soft material that fits over the door latch. It is thin enough to allow the door to close, and at the same time, prevent it from hitting the frame to avoid noise. The cushion allows quiet entry and exit through any door. It also eliminates the need to turn a doorknob every time you want to open the door. It eliminates all other sounds that are associated with opening and closing a door.

9. Draft Stop Cloth

This is a long thin tube o fabric that is placed at the bottom of the door to stop smells from getting through. It was primarily made to improve heating during winter. The material can also keep doors from slamming. The fabric design works to solve various door problems including slamming.

10. Door Damper

Slamming noise does not only comes from the door’s contact with the frame, but it can also happen as a result of contact with the adjacent wall. When the door is opened, if the knob hits the wall, it produces a slamming noise as well. The knob may create a dent in the wall, causing another damage entirely. This is when the door damper is useful to protect the wall and keep the door from slamming when it is swung open. Door dampers are metal cushion materials that keep the door from damaging the wall and making slamming noise.

Conclusion

To keep your door from slamming open is not a difficult task. It can be accomplished by simple and yet effective methods that we have reviewed in this article. They include anti-slam products and do it yourself techniques to prevent door sound.

You can begin by inspecting the hinges, whether to tighten the hinge screws or replace the hinges completely. We also highlight the effect of the doorstop, felt pad, cushions, and door closer as prime methods to prevent door slamming noise. To reduce the contact with the frame we suggested door silencer, pinch guard, and jamb cushion. All these deliver a great result to stop the door from slamming. 

👉 CLICK HERE to Subscribe for Canada jobs with visa sponsorship

Author: EasyInfoBlog Editor